Lathe - Revision history

SimoneTognetti: /* Lathe controls */

2010-02-03T16:36:44Z

‎Lathe controls

SimoneTognetti: /* Lathe controls */

2010-02-03T16:32:50Z

‎Lathe controls

SimoneTognetti at 14:19, 3 February 2010

2010-02-03T14:19:40Z

SimoneTognetti at 14:04, 3 February 2010

2010-02-03T14:04:53Z

SimoneTognetti: /* Power on/off */

2010-02-03T14:04:24Z

‎Power on/off

SimoneTognetti: /* How to use */

2010-02-03T11:57:44Z

‎How to use

SimoneTognetti at 11:02, 3 February 2010

2010-02-03T11:02:10Z

SimoneTognetti at 10:59, 3 February 2010

2010-02-03T10:59:33Z

SimoneTognetti at 10:56, 3 February 2010

2010-02-03T10:56:49Z

SimoneTognetti at 10:31, 3 February 2010

2010-02-03T10:31:38Z

@@ Line 33: / Line 33: @@
 * choos the tool to use according to the type of work to perform
 * Move longitudinally the tool close to the piece
-* Do a first fine work to make the zero. This operation means to performa a first work of the piece going in and then out in order to remove a little part of material. When the tool is out of the piece, reset measuring instruments to keep track of the zero reference position.
+* Do a first fine work to make the zero. This operation means to perform a first work of the piece going in and then out in order to remove a little part of material. When the tool is out of the piece, reset measuring instruments to keep track of the zero reference position.
 * Do the work: Move the control to the desired step (i.e 2mm) and do the work.
@@ Line 43: / Line 43: @@
-Remember that for a manual movement use both hands to rotate slowly the control. For an automatic movement remember to adjust correctly the control, since the same lever is used to perform the longitudinal or the orizzontal movement.
+Remember that for a manual movement use both hands to rotate slowly the control. For an automatic movement remember to adjust correctly the control, since the same lever is used to switch between the automatic longitudinal or orizzontal movement.
 If the tool is goog enough only small pieces of materia are cutted away. Long pieces of material means that we are not using a good tool, it can broke suddenly. Stop the work and prepare the tool with a specific machine(TODO)

@@ Line 30: / Line 30: @@
 A typical way to use the late is characterized by the following steps:
-* placd the piece to work
+* place the piece to work in the rotating part of the lathe
-* Move longitudinally close to the piece
+* choos the tool to use according to the type of work to perform
-* Fine tuning: Do a first fine work to make the zero. This mean goin in and then out removin a little part of material. When the tool is out of the piece, reset measuring instruments. Move the control again to the desired step (i.e 2mm), to the work.
+* Move longitudinally the tool close to the piece
 Remember that for a manual movement use both hands to rotate slowly the control. For an automatic movement remember to adjust correctly the control, since the same lever is used to perform the longitudinal or the orizzontal movement.
 If the tool is goog enough only small pieces of materia are cutted away. Long pieces of material means that we are not using a good tool, it can broke suddenly. Stop the work and prepare the tool with a specific machine(TODO)

@@ Line 1: / Line 1: @@
 '''(Jet WMH Tool Group) BD-8 Metal Lathe  Diameter 20/450 mm'''
 (Located at Airlab Lambrate).
 [[Image:Tornio.jpg]]

@@ Line 1: / Line 1: @@
 '''(Jet WMH Tool Group) BD-8 Metal Lathe  Diameter 20/450 mm'''
-Airlab Lambrate.
+(Located at Airlab Lambrate).
 [[Image:Tornio.jpg]]

@@ Line 12: / Line 12: @@
 [[Image:Control_panel.jpg]]
-Switch on the square button I/0 on the bottom part of the control panel.
+Switch the square button on the bottom part of the control panel to power on/off the lathe.
-Red Rounded botton sorrounded by a yellow circle line is used for a rapid stop. Press to blok, rotate to unblok the lathe.
+The red Rounded botton sorrounded by a yellow circle is used for Emergency STOP. If something is going wrong press it quicly to stop the lathe. Rotate to unblok the lathe.
 Oval buttons under the display are used for:
 * I(green): start the movement

← Older revision		Revision as of 11:57, 3 February 2010
Line 23:		Line 23:

	There exists a control to disconnect the part which keep the piece from the motor but it unuseful.		There exists a control to disconnect the part which keep the piece from the motor but it unuseful.
		+
		+	==== Lathe controls ====
		+	[[Image:Tornio_control.jpg]]
		+
		+	A typical way to use the late is characterized by the following steps:
		+	* placd the piece to work
		+	* Move longitudinally close to the piece
		+	* Fine tuning: Do a first fine work to make the zero. This mean goin in and then out removin a little part of material. When the tool is out of the piece, reset measuring instruments. Move the control again to the desired step (i.e 2mm), to the work.
		+
		+	Remember that for a manual movement use both hands to rotate slowly the control. For an automatic movement remember to adjust correctly the control, since the same lever is used to perform the longitudinal or the orizzontal movement.
		+
		+	If the tool is goog enough only small pieces of materia are cutted away. Long pieces of material means that we are not using a good tool, it can broke suddenly. Stop the work and prepare the tool with a specific machine(TODO)

@@ Line 18: / Line 18: @@
 * O(red): stop the movement
 * Up arrow / Down arrow: Invert the rotation movement
-* + / - : Adjust the rotation speed. The speed depends on the material to work and to the type of lavoration: 300g/m for a rough lavoration, 600 g/m for a fine lavoration. 300g/m is good for Iron, Alluminium. For plastic, very slow rotation with high longitudinal velocity
+* + / - : Adjust the rotation speed. The speed depends on the material to work and to the type of lavoration: 300g/m for a rough lavoration, 600 g/m for a fine lavoration. 300g/m is good for Iron, Alluminium. For plastic, very slow rotation with high longitudinal velocity.
 There exists a control to disconnect the part which keep the piece from the motor but it unuseful.

← Older revision		Revision as of 10:56, 3 February 2010
Line 1:		Line 1:
−	==(Jet WMH Tool Group) BD-8 Metal Lathe Diameter 20/450 mm ==	+	'''(Jet WMH Tool Group) BD-8 Metal Lathe Diameter 20/450 mm'''
		+	Airlab Lambrate.
	[[Image:Tornio.jpg]]		[[Image:Tornio.jpg]]
		+
		+
		+	== How to use ==
		+	This is a short manual that describes how to use this tool. The manual came out from the course held in 2009. Note that only the people that have followed that course are allowed to use such machine!
		+
		+	==== Power on/off ====
		+	If you are allowed to use the lathe use you personal key to switch on the general supply.
		+	[[Image:Control_panel.jpg]]
		+	Switch on the square button I/0 on the bottom part of the control panel.
		+	Red Rounded botton sorrounded by a yellow circle line is used for a rapid stop. Press to blok, rotate to unblok the lathe.
		+	6 Oval buttons under the display are used for:
		+	* I(green): start the movement
		+	* O(red): stop the movement
		+	* Up arrow / Down arrow: Invert the rotation movement
		+	* + / - : Adjust the rotation speed. The speed depends on the material to work and to the type of lavoration: 300g/m for a rough lavoration, 600 g/m for a fine lavoration. 300g/m is good for Iron, Alluminium
		+
		+	There exists a control to disconnect the part which keep the piece from the motor but it unuseful.

← Older revision		Revision as of 10:31, 3 February 2010
Line 1:		Line 1:
	==(Jet WMH Tool Group) BD-8 Metal Lathe Diameter 20/450 mm ==		==(Jet WMH Tool Group) BD-8 Metal Lathe Diameter 20/450 mm ==
−	[[Image:~~Zoom_img_1_20090824132345~~.jpg]]	+	[[Image:Tornio.jpg]]